Setting up Procedure in Detail

Bios - Settings

• Advanced BIOS Features [ Enter ]
  
  
  • Anti-Virus Protection [ Disabled ]
  • CPU L1 & L2 Cache [ Enabled ]
  • Quick Power On Self Test [ Enabled ]
  • First Boot Device [ Floppy ]
  • Second Boot Device [ CDROM ]
  • Third Boot Device [ HDD-0 ]
  • Boot Other Device [ Enabled ]
  • Swap Floppy Drive [ Disabled ]
  • Boot Up Floppy Seek [ Disabled ]
  • Boot Up Numlock Status [ On ]
  • Gate A20 Option [ Fast ]
  • Typematic Rate Setting [ Disabled ]
  • Security Option [ Setup ]
  • MPS Version Control for OS [ 1.1 ]
  • OS (Select for DRAM > 64MB) [ Non-OS2 ]
  • Small Logo (EPA) Show [ Enabled ]
  • HDD Instant recovery [ Disabled ]
  • Show POST CODE [ Disabled ]
• Power Management Setup [ Enter ]
  
  
  • ACPI Function [ Enabled ]
  • ACPI Suspend Type [ S1(POS) ]
  • Power Management [ User Define ]
  • Video Off Method [ DPMS ]
  • Video Off In Suspend [ No ]
  • Suspend Type [ Stop Grant ]
  • MODEM Use IRQ [ 3 ]
  • Suspend Mode [ Disabled ]
  • HDD Power Down [ Disabled ]
  • Soft-Off by PWR-BTTN [ Instant-Off ]
  • Primary IDE 0 [ Disabled ]
  • Primary IDE 1 [ Disabled ]
  • Secondary IDE 0 [ Disabled ]
  • Secondary IDE 1 [ Disabled ]
  • FDD,COM,LPT Port [ Disabled ]
  • PCI PIRQ[A-D]# [ Disabled ]
  • Wake Up Events [ Enter ]
    
    
    • Power On By PCI Card [ Disabled ]
    • Power On By Modem [ Disabled ]
    • Wake Up On LAN [ Disabled ]
    • Power On By Alarm [ Disabled ]
    • POWER ON Function [ BUTTON ONLY ]

 

Home | Return | Top

 

Fdisk

• Type [ FDISK ] at the A: prompt
• Do you wish to enable large disk support (Y/N). [ Y ]
• 1. Create DOS Partition or Logical DOS Drive. [ 1 ]
• 1. Create Primary DOS Partition [ 1 ]
• Do you wish to use the maximum available size for a Primary DOS Partition & make the Partition Active (Y/N) [ Y ]
• Press ESC to exit Fdisk
• Reboot

 

 

Home | Return | Top

Network

• My Network Place - Properties
• Local Area Connection - Properties - Install...
  
  
  • Client - Client for Microsoft Networks
  • Service - File and Printer Sharing
• Internet Protocal (TCP/IP) - Properties - Use the following IP Address
  
  
  • IP Address: 132.148.21.100
  • Subnet Mask: 255.255.0.0
• My Computer - Properties - Network Identification - Properties
  
  
  • Workgroup: Link

 

 

Home | Return | Top

Modem

• Control Panel - Internet Options - Connections - Add - Dial-up to Private Network
  
  
  • Internet Service Provider's Phone number
• Settings - Dial-up Settings
  
  
  • User Name:
  • Password:
• Properties - Networking - Internet Protocol (TCP/IP) - Properties
  
  
  • Use the Following DNS Server Addresses
    
    
    • Preferred DNS Server: ???.???.???.???
    • Alternate DNS Server: ???.???.???.???
  • OK - OK - OK
• Connections - Select (Dial-up Networking Connection)
  
  
  • Set Default
  • Always Dial my Default Connection

 

 

Home | Return | Top

Pro-ONE Drivers

• Found New Hardware Wizard [ NEXT ]
• Search for a suitable driver for my device (recommended) [ NEXT ]
• Specify a location [ NEXT ][ BROWSE... ]
  
  
  • C:\New Drivers\Pro ONE\v2.01 [ OK ][ NEXT ]
• Digital Signature Not Found
  
  
  • Do you want to continue the installation [ YES ][ FINISH ]
  • Pinnacle Pro-ONE Overlay
• Found New Hardware Wizard [ NEXT ]
• Search for a suitable driver for my device (recommended) [ NEXT ]
• Specify a location [ NEXT ]
  
  
  • C:\New Drivers\Pro ONE\v2.01 [ OK ][ NEXT ]
• Digital Signature Not Found
  
  
  • Do you want to continue the installation [ YES ][ FINISH ]
  • Pinnacle Pro-ONE E4
• Found New Hardware Wizard [ NEXT ]
• Search for a suitable driver for my device (recommended) [ NEXT ]
• Specify a location [ NEXT ]
  
  
  • C:\New Drivers\Pro ONE\v2.01 [ OK ][ NEXT ]
• Digital Signature Not Found
  
  
  • Do you want to continue the installation [ YES ][ FINISH ]
  • Pinnacle Pro-ONE (3D Renderer)

 

 

Home | Return | Top

Edit the Registry

• [ START ][ RUN ] Type the following:
  
  
  • regedit [ OK ]
• [ REGISTRY ][ EXPORT REGISTRY FILE... ] Give it a name and place in the root (C:\Backup.reg)
• Find the entry (ShuttlePRO Helper) in the following Directory
  
  
  • HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\Currentversion\Run
• Select and Delete this entry (ShuttlePRO Helper) [ YES ]
• [ REGISTRY ][ EXIT ]